Heating, Cooling, Plumbing, and Generator Services in Charlevoix, MI

Responded to service call for dual AC system evaluation and furnace tune-up. Inspected both air conditioning units and associated refrigerant lines, verifying proper operation of compressors, airflow, and temperature differential across evaporator coils. Found both AC systems functioning within normal parameters; educated client on system operation and thermostat zoning. Completed preventive maintenance on gas furnace including burner inspection, heat exchanger examination, blower motor lubrication, air filter replacement, and combustion analysis to ensure safe and efficient operation for upcoming heating season.

Conducted on-site evaluation for mini-split cooling system installation. Assessed existing electrical infrastructure, documenting 200-amp main service panel with adequate capacity for additional HVAC equipment. Customer requested cooling options and was uncertain about current heating system type, requiring full assessment of mechanical systems to determine compatibility and optimal mini-split configuration.

Completed annual preventive maintenance on outdoor standby generator unit as requested. Performed comprehensive tune-up service including visual inspection of all accessible components, verification of proper operation, and documentation of equipment condition. Opened access panels to inspect internal mechanical and electrical systems including engine assembly, battery connections, fuel system components, and control modules. Verified all wiring connections were secure with no signs of corrosion or damage. Confirmed insulation material on enclosure lid remains intact and effective. Generator housing and exterior components found to be clean and well-maintained with no visible deterioration. Unit operational and ready for service.

Responded to inspection correction for improperly installed zone valve damper in crawlspace ductwork serving the den area. Located the zone damper near the line set and confirmed it was installed backwards in the duct run. Corrected the damper orientation to ensure proper airflow direction and system operation.

Conducted on-site assessment for new furnace installation in residential property with no existing heating system. Evaluated interior spaces including main living area, stairwell access points, and potential equipment placement locations to determine optimal installation configuration and routing for ductwork and venting systems. Documented site conditions and structural layout to prepare comprehensive furnace installation estimate.

Completed AC startup service on residential cooling system. Performed comprehensive system inspection, verified refrigerant levels, tested electrical connections, and confirmed proper operation of all components. Unit is functioning within manufacturer specifications and ready for cooling season.

Replaced frozen dishwasher solenoid valves with new unit that had been previously ordered and received. Accessed property using provided entry information, completed installation of replacement valve, and tested system for proper operation.

Completed HVAC installation in basement crawl space, including mounting air handler unit with proper electrical connections and conduit routing. Installed flexible ductwork with reflective insulation wrap and sealed all connections with foil tape to prevent air leakage and pest intrusion. Verified outdoor condenser unit connections, condensate drain lines, and electrical service are properly secured and operational.

Responded to first call of the day to restore water service to property. Main water supply had been previously shut off and required reactivation to provide water access for workers on site. Successfully turned water back on and verified proper flow, then contacted appropriate party to confirm completion of service request.

Completed routine maintenance and tune-up on 16-year-old OHVI engine generator unit located in attic space. Performed standard preventative maintenance procedures including inspection of all engine components, oil system check, fuel system evaluation, and verification of proper operation. Unit tested successfully and returned to service with all systems functioning within normal parameters.

Responded to generator fault indication with red warning light activation. Inspected exterior gas line assembly and brass ball valve connection at generator fuel supply point. Documented piping configuration and valve installation mounted on building exterior. System evaluated and photographed for service records.

Completed full HVAC system installation including a new 16.5 SEER2 Bryant outdoor condensing unit mounted on pad with corresponding cased evaporator coil integrated with existing Goodman furnace in basement utility area. Additionally installed mini split heat pump system with outdoor condensing unit and indoor head unit. Installed ceiling-mounted bathroom exhaust fan with dedicated electrical circuit, ran venting through attic space, and terminated through soffit for proper exterior discharge.

Responded to service call for 3-year-old residential standby generator with no-start condition. Upon arrival, found unit cranking but failing to start, with Evolution 2.0 controller displaying "SWITCHED TO OFF" and "LOSS OF PROTECTION" error messages. Performed diagnostic evaluation of generator system, documented control panel status and equipment condition. Unit was previously shut down by homeowner due to starting failure.

Conducted on-site assessment of existing HVAC system to provide estimate for Energy Recovery Ventilator (ERV) or Heat Recovery Ventilator (HRV) installation. Evaluated current mechanical room configuration, including furnace/air handler unit, ductwork infrastructure, and available space for ventilation equipment integration. Documented existing equipment layout and utility connections to determine optimal placement and installation requirements for proposed ventilation system upgrade.

Completed on-site assessment for furnace and air conditioning system replacement estimate. Inspected existing HVAC equipment installation including ductwork, condensate drainage lines, flexible conduits, and electrical connections in mechanical space. Documented current system configuration with photographs showing equipment mounting, PVC drain piping, metallic flex lines, and associated plumbing components to develop comprehensive replacement proposal.

Conducted on-site evaluation for air conditioning system and bathroom fan installation estimate. Inspected existing HVAC equipment including furnace unit, air handler, and ductwork configuration. Documented significant condensation accumulation on metal ductwork indicating potential inadequate insulation or humidity control issues. Noted current filter size specifications at 16x24x1 and assessed overall system condition including aging components with visible wear patterns. Evaluated mechanical space accessibility and existing infrastructure to determine scope of work for AC installation and bathroom ventilation fan addition. Captured photographic documentation of equipment layout, ductwork routing, and moisture concerns to support estimate preparation.

Responded to gas leak concern with reported high CO2 readings in residential property with 20+ year old equipment. Performed comprehensive safety inspection of basement mechanical room housing water heater and furnace unit, as well as crawl space area with exposed HVAC ductwork. Conducted combustion analysis and gas leak detection throughout all equipment and connection points, verified proper ventilation, and documented equipment condition with photos for service records.

Completed AC startup on newly installed system. Verified proper refrigerant levels, electrical connections, and condensate drainage through exterior PVC piping. All equipment operating within manufacturer specifications with adequate airflow confirmed.

Removed and disposed of existing water heater and installed new power vented unit in basement utility room. Installation included new 1/4 turn shutoff valves, reconnection of gas line, PVC vent piping, copper water supply lines, and electrical connections. Maintained water supply to existing humidifier system to ensure continued operation of HVAC equipment.

Performed annual heating system inspection on Bryant furnace. During inspection, discovered a gas leak at the generator coupling located downstream of the gas shutoff valve. The coupling showed signs of corrosion and oxidation, with visible weathering on the connection components. Immediately shut off gas supply to the generator to eliminate the safety hazard. Documented the leak location with photographs showing the corroded coupling between the black flexible gas line and metallic corrugated line. Unit failed inspection due to this gas leak violation and requires coupling replacement before system can be safely returned to service.