Heating, Cooling, Plumbing, and Generator Services in Charlevoix, MI

Completed full air conditioning system replacement at residential property. Removed existing AC unit and installed new Bryant condenser on exterior concrete pad against house wall. Unit properly positioned with adequate clearance for airflow and service access. Verified electrical connections, refrigerant lines, and condensate drainage. System commissioned and tested for proper operation. All debris removed from work area, site left clean with decorative stone landscaping undisturbed around equipment pad.

Completed on-site evaluation of existing Weil-McLain boiler system and associated hydronic heating components in residential mechanical room. Documented current installation including water heater, expansion tank, multiple zone circulation pumps with individual controls, complex copper piping network with various shut-off valves, and flexible connector hoses. Photographed system configuration showing aged piping with mineral deposits, electrical connections, PVC venting, and multi-zone manifold setup with red circulation pumps and ball valves for zone isolation. Provided comprehensive estimate for boiler replacement and system upgrades based on assessment of existing equipment condition and installation requirements.

Completed removal and disposal of existing 2-ton air conditioning system including condenser unit and pad. Installed new Bryant HVAC system consisting of furnace with drain pan and 2-ton Puron condenser unit on concrete pad. New equipment positioned on exterior concrete pad with proper electrical disconnect and conduit installation, while furnace installed in mechanical room with PVC venting routed through ceiling and connected to existing ductwork.

Conducted on-site evaluation of existing HVAC system for air conditioning replacement estimate. Documented current installation including Rheem furnace unit, refrigerant lines, PVC condensate drain and venting configuration, and electrical connections. Photographed equipment layout, piping arrangements, wire terminations with multiple junction points, and mechanical room constraints to provide comprehensive assessment for complete AC system replacement proposal.

Responded to service call for carbon monoxide alarm inspection and foundation vent screening installation. Installed fine mesh screening over crawl space foundation vents to prevent pest entry while maintaining proper ventilation, replacing gaps left from previous installation work. Verified proper screen fit and secure attachment to prevent animal intrusion. Conducted carbon monoxide level testing throughout the property to ensure safe readings and proper alarm function. All CO levels measured within normal safe parameters with no elevated readings detected.

Responded to inspector correction request for HVAC unit serial number verification. Previous serial number reported as invalid by inspector. Photographed manufacturer specification label and equipment data plates on unit to document correct serial number and model information for compliance verification.

Conducted site assessment for whole home standby generator installation. Evaluated existing electrical service infrastructure, documenting 200-amp main service panel with Stratus IQ digital meter and current electrical capacity. Photographed meter base configuration, service entrance location, and available installation area adjacent to existing HVAC equipment on exterior foundation. Assessed clearance requirements, utility access points, and optimal generator placement on concrete pad near house perimeter. Reviewed electrical load requirements and transfer switch integration options with existing 240V three-wire service. Prepared comprehensive estimate for complete standby generator system installation including equipment specifications, transfer switch, and necessary electrical connections.

Conducted comprehensive site assessment for complete boiler replacement estimate at residential property. Evaluated existing hydronic heating system including aging boiler unit and Reliance water heater with associated copper piping, gas lines, and venting infrastructure in basement utility area. Documented current equipment configuration, photographed mechanical connections, and assessed feasibility of multiple replacement options including modern boiler system installation versus alternative forced-air HVAC conversion, as well as potential integrated water heater replacement to optimize overall system efficiency and performance.

Conducted site assessment for new high velocity HVAC system installation in older home without existing high velocity equipment. Inspected attic space to evaluate structural conditions, available routing pathways, and installation feasibility for compact ductwork and air handler placement. Documented existing attic configuration including storage layout, framing structure, access points, and observed what appears to be current HVAC components including flexible ductwork and mechanical equipment mounted on support framework. Photographed attic conditions to support system design and provide accurate quote for complete high velocity system installation.

Conducted comprehensive site assessment of existing multi-unit HVAC system installation featuring multiple air conditioning condensers including Trane equipment positioned on exterior concrete pad. Documented current electrical infrastructure including disconnect boxes and circuit breaker panel schedule, photographed equipment configuration and electrical distribution setup to develop accurate replacement estimate for aging AC system.

Conducted comprehensive estimate for complete HVAC system conversion from all-electric split system to heat pump with gas backup capability. Property currently equipped with electric radiant baseboard heaters in individual rooms with separate thermostats and central forced air air conditioning only. Evaluated existing electrical service panel showing adequate breaker capacity and reviewed digital utility meter installation on exterior. Assessed feasibility of full heat pump conversion including replacement of outdoor condenser unit and indoor air handler while retaining existing baseboard heaters as supplemental heat source. Documented requirement for new gas line installation from utility provider to enable future gas heating option, noting entire residence currently operates on electric service. Photographed electrical infrastructure including main distribution panel with available breaker slots and exterior meter base configuration to support system upgrade planning and load calcula

Removed previously installed instant hot water system and replaced with Franke Little Butler HT-300 Instant Hot Water System per original customer specification. Unit was ordered from Fresh Water System, received, and installed on marble countertop with proper electrical connection and water supply lines.

Responded to no cooling complaint on Armstrong air conditioning system. Upon arrival, connected refrigerant manifold gauges to service ports and performed diagnostic testing. System readings indicated abnormal operating pressures and temperatures, confirming inadequate cooling performance. Conducted comprehensive system evaluation including pressure testing, temperature differential measurements, and visual inspection of all accessible components. Identified issues affecting system performance and cooling capacity. Performed complete tune-up service as requested by customer, which included inspection of evaporator coil assembly, blower components, and refrigeration circuit connections. Documented system operating conditions with diagnostic gauge readings showing suction and discharge pressures, superheat, subcooling, and saturation temperatures. Inspected refrigerant line connections and service valve assemblies for proper operation. Addressed cooling deficiency and restored system

Completed full AC system replacement at residential property. Installed new outdoor condenser unit on concrete pad against exterior wall with proper electrical conduit connection and refrigerant line routing. Unit positioned on side yard location with adequate clearance for airflow and service access, tested and verified operational.

Provided estimate for replacement of 30+ year old Comfortaire wall-mounted HVAC system in condo unit, consisting of indoor wall unit (23.75" W x 17.25" H x 14" D) with corresponding outdoor condenser unit located on deck. Inspected existing system including wall-mounted control panel with mechanical dial controls and portable supplemental air conditioning unit, documented equipment dimensions and configuration, and assessed installation requirements for replacement system.

Conducted on-site assessment for boiler replacement estimate. Evaluated existing heating system infrastructure, including electrical panel configuration and current water heater installation, to determine compatibility requirements and necessary modifications for new boiler system installation.

Conducted comprehensive estimate for complete furnace and air conditioning system replacement. Evaluated existing HVAC installation including current air handler unit, ductwork configuration with TRION Air Bear filtration system, and mechanical room layout. Assessed vertical main supply trunk, flexible duct connections, and overall system accessibility for replacement equipment. Documented existing plumbing infrastructure, water heater proximity, and utility room constraints to determine optimal equipment placement and installation requirements. Photographed current equipment specifications, duct configuration, and mechanical space conditions to provide accurate proposal for new high-efficiency heating and cooling system installation.

Provided estimate for air conditioning system replacement. Inspected existing HVAC equipment including basement-installed furnace/air handler with PVC venting and attic-mounted evaporator coil unit (Nordyne model C3RA-048C-C utilizing R22 refrigerant). Customer inquired about honoring previous quote from August; explained standard 60-day estimate validity period and documented current system conditions with photographs for updated pricing.

Removed and disposed of existing finned tube baseboard heating from living room and old boiler system with accessories from basement. Installed new 95% efficient tankless combination boiler with integrated domestic hot water supply, complete with copper piping network, pressure gauges, isolation valves, and PVC venting system. System was fully commissioned and tested for proper operation of both space heating and domestic water functions.

Responded to service call for dual AC system evaluation and furnace tune-up. Inspected both air conditioning units and associated refrigerant lines, verifying proper operation of compressors, airflow, and temperature differential across evaporator coils. Found both AC systems functioning within normal parameters; educated client on system operation and thermostat zoning. Completed preventive maintenance on gas furnace including burner inspection, heat exchanger examination, blower motor lubrication, air filter replacement, and combustion analysis to ensure safe and efficient operation for upcoming heating season.